Accueil
Appareil: 
Vol ID: device/9c13-9ed2-7230Afficher événements
Télécharger
Ajuster temp. & pression ?
Image
Jeux de données
Cliquez sur la légende pour afficher ou masquer les données
Zoom
Cliquez-glissez ou pincez sur mobile
Comparer un vol ?
Notes utilisateur
Ajoutez cet appareil à votre compte pour modifier
Vidéo Youtube
Aucune vidéo
Ajoutez cet appareil à votre compte pour modifier
Images du vol (2)
Fusée associée
Aucune fusée associée à ce vol
Informations appareil
Moteurs du vol
Aucun moteur ajouté à ce vol
Ajoutez cet appareil à votre compte pour modifier
Paramètres généraux
Ceci est un aperçu des paramètres utilisés pour ce vol. Rendez-vous sur la
Rendez-vous sur la page Mes appareils puis Configurer les paramètres..
Pression prévue
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
mbar
Détection lancement
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
meters
Ratio échantillonnage
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:
Max. échantillons
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
Arrêt enregistrement
i
This setting is how the altimeter decides to stop recording. You can choose either 300 or 600 samples stable or it will record until it's 10000 sample limit unless you press the BUTTON in Manual stop mode.
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Suréchantillonnage
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
Filtre IIR
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
Filtre pression
i
This filter is a software Kalman filter that runs on the altimeters processor.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
Verrouillage lancement
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
ENABLED
Température statique
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C
Commentaires
Commentaires
Connectez-vous pour commenter.
Connectez-vous pour commenter.