Podsumowanie lotu

Wysokość

Apogeum

172.14 Metry

Czas do apogeum

6.5 seconds

Wysokość wypalenia

85.76 m

Wys. maks. prędkości

75.47 m

Wys. wyrzutu

0.2 m

Wys. lądowania

-7.06 m

Stabilność

Wskaźnik stabilności

0.1 / 100 (Słaby)

Rozkład stabilności

Nachylenie przy wypaleniu (20%)0

Stałość nachylenia (15%)0

Prędkość pochylania/odchylania (30%)0

Tłumienie (20%)0

Prostoliniowość ciągu (15%)0

Prędkość

Maks. wznoszenie

51.77 m/s

Maks. opadanie

-45.96 m/s

Przy wypaleniu

50.800 m/s

Prędk. lądowania

-39.913 m/s

Prędk. opadania

-28.000 m/s

Prędk. wyrzutu

3.76 m/s

Recovery

Single deploy (no dual deploy detected)

Przyspieszenie

Maks. wznoszenie

6.13 G

Maks. opadanie

0.12 G

Maks. podczas spalania

6.13 G

Śr. wznoszenie

1 G

Śr. spalanie

2.86 G

Czasy

Wypalenie (pierwszy)

2.54 seconds

Apogeum

6.5 seconds

Možliwy wyrzut

0 seconds

Lądowanie

13.35 seconds

Wyjście #1 WŁ

0 seconds

Wyjście #1 WYŁ

0 seconds

Kąty

Nachylenie rampy

65.04°

Maks. nachylenie do wypalenia

94.93°

Przechylenie startowe

59.94°

Pochylenie startowe

-32.60°

Maks. obrót (spal.)

1859.39 dps

Śr. obrót (spal.)

1220.08 dps

Ogólne

Data przesłania

27-Mar at 13:19

Próbki danych

1285

Całkowity czas nagrania

25.900 s

Śr. próbki/s

49.6

Liczba blokad

1

Wysokość nagrywania

3.23 m

Start po włączeniu

53m 17s

Oś referencyjna

Y

Bateria & temperatura

Bateria początek

44%

Bateria koniec

44%

Temperatura początek

14.9°C

Temperatura koniec

14.75°C

Temp. MT1 startowa

0°C

Reguły wyjścia

Brak skonfigurowanych reguł

Animacja danych lotu

FLIGHT 1405

172.14 Meters

ALTITUDE

0.00m

VELOCITY

0.00m/s

ACCEL

0.00G

TILT

0.00°

PITCH

0.00°

ROLL

0.00°

YAW

0.00°

TIME

0.00s

AWAITING LAUNCH

ALT

altimetercloud.com

LAUNCH T+0.00s LANDING

Uwaga: Animacja lotu wymaga montażu wysokościomierza w stałej orientacji. Skalibruj czujniki dla najlepszych wyników.

Notatki užytkownika

Dodaj to urządzenie do swojego konta, aby edytować

Film Youtube

Brak filmu

Dodaj to urządzenie do swojego konta, aby edytować

Zdjęcia lotu (0)

Brak zdjęć

Powiązana rakieta

Žadna rakieta nie jest powiązana z tym lotem

Informacje o urządzeniu

Mercury V1

Ten lot został wykonany na Mercury V1.

Wersja sprzętu

Rev 2

Wersja oprogramowania

2.0

Ostatnio online

27-Mar at 13:19

Akcelerometr

32G 3-axis

Gyroskop

2000 dgps 3-axis

Czujnik ciśnienia

Bosch BMP 390

Magnetometr

N/A

2 Więcej z tego wysokościomierza → 2 Tag: #Altimeter B → Specyfikacje wysokościomierza →

Silniki lotu

Nie dodano silników do tego lotu

Dodaj to urządzenie do swojego konta, aby edytować

Miejsce startu, data i godzina

Kliknij na mapę · Przeciągnij, aby dostosować

Lat— Lng—

✓ Launch location saved successfully.

✗ Could not save location — please try again.

Reguły wyjścia

Reguły pozwalają Mercury wykonywać akcje na podstawie warunków lotu. Každa reguła ma do 4 warunków (A-D).

Brak skonfigurowanych reguł

Dopasowanie silnika (BETA)

Wciąż w trybie testowym! Pracujemy nad ustaleniem, jaki silnik był użyty.

Marka

Silnik

Wynik

Kształt

Spalanie

Contrail

G300

33

73.5%

77.3%

AeroTech

H669N

33

78%

67.7%

AeroTech

I1299N

23

20.8%

68.8%

Estes

1/4A3T

22

-33.8%

58.2%

Cesaroni

68-F240-VM-15A

18

27.4%

72.7%

Cesaroni

25-E75-VM-17A

14

48.1%

75.6%

Estes

1/2A6

12

-41%

55.5%

Estes

1/2A3T

0

27.2%

61.8%

Quest

A6Q

0

-3.1%

72%

Quest

B14T

0

15.7%

64.7%

Spalanie silnika

To jest wielkość wyjściowa akcelerometru od startu do wypalenia. You can check this against your motors thrust data on thrustcurve.org.

Ogólne ustawienia lotu

To jest migawka ustawień użytych dla tego lotu. Przejdź na Przejdź na stronę Moje urządzenia i skonfiguruj ustawienia..

Ciśnienie prognozowane

i

Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!

Xcweather.co.uk is a decent place to grab pressures from for your location and time.

1013.2 mbar

Detekcja startu

i

This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.

The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.

For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.

25 meters

Sample ratio

i

The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.

1:1 (50Hz)

Max samples

i

This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.

12000

Recording stop

i

This setting is how the altimeter decides to stop recording. You can choose either 300 or 600 samples stable or it will record until it's 10000 sample limit unless you press the BUTTON in Manual stop mode.

The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).

Auto: 300 samples stable

Oversampling

i

Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.

The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.

8x Oversampling

IIR filter

i

The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.

We suggest not setting this too high as it will cause delay to changes in altitude if set very high.

COEFF 7

Pressure filter

i

This filter is a software Kalman filter that runs on the altimeters processor.

The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.

Kalman 2 (default)

Lockout time

i

The Lockout time is how long the altimeter should stop making decisions and taking actions if it detects unusual high speed altitude changes that are unexpected.
These false readings can be caused by ejection charges (if the altimeter is in the same compartment as the motor ejection gases) or even when you transition to Mach speeds and can give false readings of altitude changes.

When these events are detected the system enters Lockout for the specified time while it stabalises. This effects things like triggering the output, or calculating other data.

750ms

Lockout change

i

This is how we detect a lockout. If the pressure changes by this much in a single sample downwards (pressure increase, lower altitude) then it's likely to be a false reading. Multiply the setting by 32 to get the speed in meters per second that it will trigger at.

1.5 meters

Sync sensors

i

The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data. The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.

WŁĄCZONY (24 samples / 468.00ms)

Orientation

i

This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.

Upwards (text up)

IMU filter

i

The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical. These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.

Madgwick 6-Axis

Launch ALP

i

This is prevention against accidental launch detection.

With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.

With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.

There are very few situations where this option would cause issues, so we suggest leaving it on.

1.4G

Launch lock

i

When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.

DISABLED

Static temperature

i

A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.

15.00 °C

Temp sensor

i

If an external MT1 temperature sensor is connected, this controls whether it is used for logging only or also for altitude calculations.

DISABLED

Ustawienia wyjścia

To jest migawka ustawień użytych dla tego lotu.

Wyjście 1 aktywne

i

Disable or enable the output from being able to turn on or off.

WYŁĄCZONY

Wyjście 1 wyzwalacz

i

After apogee (altitude)

This method triggers when the altitude drops below the set altitude after apogee is detected.

After apogee (time)

This method triggers the defined seconds after apogee is detected.

After launch (altitude)

This method is activated if/once the altimeter exceeds the set altitude after launch.

After launch (time)

This option triggers the defined seconds after launch is detected.

After burnout (time)

This method triggers the defined seconds after burnout is detected.

After apogee (altitude)

Wyjście 1 czas włączenia

i

This is how long the output should trigger ON state when the rules are met.

2000ms

Wyjście 1 wysokość

i

This is the altitude to trigger at if using a trigger method that works on altitude.

For example if you set this to 75m and After apogee (altitude) for the trigger then the output will turn on at 75m on descent above the launch altitude.

0 meters

Wyjście 1 czas

i

This is the time variable for output triggers that work on time.

For example if you set this to 3 seconds and After apogee (time) as the trigger then the output will turn on 3 seconds after apogee.

0 seconds

Blokada wysokości

i

Altitude lock is a safety feature that prevents the output from triggering if the altitude is below this level when the rules are met.

50.00 m

Blokada kąta nachylenia

i

This is another safety feature. It can be used to disable the output if the rocket has gone too far from vertical.

For example if you set the tilt angle lock to 40 degrees then the output will not fire if the rocket is more than 40 degrees from vertical. To disable set this to 0.

0.00 °

Kalibracja czujników

Przesunięcia kalibracji użyte w tym locie.

Gyroskop

⚠ Gyroskop nie został skalibrowany

X

0.000°

Y

0.000°

Z

0.000°

Akcelerometr

⚠ Akcelerometr nie został skalibrowany

X

0.000 mG

Y

0.000 mG

Z

0.000 mG

Ustawienia urządzenia

To jest migawka ustawień użytych dla tego lotu.

TAG urządzenia

i

A custom name or tag assigned to this device for easy identification.

Altimeter B

Język

i

The language setting configured on the device.

en

Tryb wyłączania

i

Controls what happens after recording. Standard shuts down normally, Delayed keeps WiFi on for 30 seconds after landing, Stay on keeps the device powered on.

Delayed 30s

Jasność LED

i

The brightness level of the LED indicators on the Mercury. Lower values save battery.

20%

WiFi TX power

i

WiFi transmit power level. Higher gives better range but uses more battery.

5 dBm (default)

Tryb uśpienia

i

Controls whether the device enters low-power sleep when idle.

Normal (sleep when idle)

Monitor baterii

i

Monitors battery voltage during the flight.

DISABLED

Cloud group

i

The cloud group / category this flight is assigned to.

Porty GP6 / GP7

Konfiguracja portów GP6 i GP7 dla kanałów pirotechnicznych, serw lub innych urządzeń.

Channel 6 mode

ON = HIGH

Ch6 min pulse (µs)

1000

Ch6 max pulse (µs)

2000

Ch6 frequency

50 Hz

Ch6 angle ON

170.00°

Ch6 angle OFF

10.00°

Ch6 on time

2.00s

Channel 7 mode

ON = HIGH

Ch7 min pulse (µs)

1000

Ch7 max pulse (µs)

2000

Ch7 frequency

50 Hz

Ch7 angle ON

170.00°

Ch7 angle OFF

10.00°

Ch7 on time

2.00s

Płytka servo I2C PCA9685

To jest migawka ustawień użytych dla tego lotu.

Configuration for the external I2C PCA9685 servo expansion board. This board provides up to 6 additional servo channels.

No I2C servo board was connected for this flight.

Prognoza i hamulce powietrzne

Ta funkcja nie była dostępna przed wersją 2.10+

Witamy ponownie

Utwórz darmowe konto

FLIGHT 1405

BURNOUT