Dónde comprar Actualizador de firmware Configuración USB WiFi Subida de registros Guías
Inicio Dispositivo: Vuelo ID: 2668/
Distancia
Elija la unidad de distancia: Metros(m), Pies(ft), Millas(mi) o Kilómetros(km)
Velocidad
Elija la unidad de velocidad: m/s, ft/s, mph o km/h
Aceleración
Elija la unidad de aceleración: m/s² o G
Vuelo 2668/

Flight 2668/

Apogeo
0m
s after launch
Máx. ascenso
peak ascent
Máx. durante combustión
0
during the burn
Aterrizaje
s
touchdown
ZOOM TO
s
s
Mostrar eventos
Descargar
Ajustar temp. & presión ?
Imagen
Zoom
Clic y arrastre, o pellizco en móvil
Comparar vuelo ?
Borrar
Notas del usuario
Sin notas
Añada este dispositivo a su cuenta para editar
Vídeo Youtube
Sin vídeo
Añada este dispositivo a su cuenta para editar
Imágenes del vuelo 0
Sin imágenes
Motores del vuelo
No se han añadido motores a este vuelo
Añada este dispositivo a su cuenta para editar
Cohete vinculado
Ningún cohete vinculado a este vuelo

Linked flights

Connect flights that belong together: a second altimeter flown in the same rocket, or the same rocket flown again. Linked flights appear on each other’s pages.

No linked flights yet.

Sitio de lanzamiento, fecha y hora

Haga clic en el mapa para marcar su sitio de lanzamiento. Cambie entre vista de mapa y satélite.

Imagery © Esri, Maxar, Earthstar Geographics

Clic en el mapa · Arrastre para ajustar

Canopy height: Version 2 High Resolution Canopy Height Maps by WRI and Meta was accessed in September 2026 from https://registry.opendata.aws/dataforgood-fb-forestsv2. Meta and World Resources Institute (WRI) - 2026. Version 2 High Resolution Canopy Height Maps (CHMv2). Source imagery for CHM © 2016 Vantor, licensed under CC BY 4.0. Where that is not yet in the database: ETH Global Canopy Height 2020, CC BY 4.0, from Lang, N., Jetz, W., Schindler, K. and Wegner, J. D. (2023), A high-resolution canopy height model of the Earth, Nature Ecology & Evolution. Both reduced to height bands by Altimeter Cloud. Ground height: Terrain Tiles (Mapzen / Tilezen, on AWS Open Data), reduced into resolution tiers by Altimeter Cloud: ArcticDEM terrain data DEM(s) were created from DigitalGlobe, Inc., imagery and funded under National Science Foundation awards 1043681, 1559691, and 1542736; Australia terrain data © Commonwealth of Australia (Geoscience Australia) 2017; Austria terrain data © offene Daten Österreichs – Digitales Geländemodell (DGM) Österreich; Canada terrain data contains information licensed under the Open Government Licence – Canada; Europe terrain data produced using Copernicus data and information funded by the European Union - EU-DEM layers; Global ETOPO1 terrain data U.S. National Oceanic and Atmospheric Administration; Mexico terrain data source: INEGI, Continental relief, 2016; New Zealand terrain data Copyright 2011 Crown copyright (c) Land Information New Zealand and the New Zealand Government (All rights reserved); Norway terrain data © Kartverket; United Kingdom terrain data © Environment Agency copyright and/or database right 2015. All rights reserved; United States 3DEP (formerly NED) and global GMTED2010 and SRTM terrain data courtesy of the U.S. Geological Survey. Map and imagery credited on the view above.

No launch site has been set for this flight.

Flights from this altimeter

No other flights yet. This will fill up as you fly.

Settings, as they were for this flight

Ajustes generales del vuelo
Presión prevista
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!

Xcweather.co.uk is a decent place to grab pressures from for your location and time.
mbar
Detección lanzamiento
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.

The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.

For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
meters
Sample ratio
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:
Max samples
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
Recording stop
i
This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.

The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Oversampling
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.

The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
IIR filter
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.

We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
Pressure filter
i
This filter is a software Kalman filter that runs on the altimeters processor.

The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
Launch lock
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
ENABLED
Static temperature
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C

Files

Where the altimeter signs its log, the file carries that signature and a tick beside it. A tick means the data is unchanged since the device wrote it, which is what a record claim needs.
Adjusted CSV2904 recalculated in your browser
The log recomputed for your own sea-level pressure and temperature. Columns: time, altitude as recorded and adjusted, raw altitude as recorded and adjusted, pressure.

This file is built here from the signed log, so it carries no signature of its own. Anyone verifying a claim should be sent to the flight page and build their own from the original.

Vuelo
Comentarios
Inicia sesión para comentar.
Inicia sesión para comentar.