Flug-ID: 1785

Lil Nuke - Flight with 4 altimeters - 2

Flugzusammenfassung

Höhe

Apogäum

756.69 Meter

Zeit bis Apogäum

11.49 seconds

Brennschluss-Höhe

117.73 m

Max. Geschw.-Höhe

142.75 m

Auswurf-Höhe

208.57 m

Lande-Höhe

-1.66 m

Stabilität

Stabilitätswert

85.3 / 100 (Ausgezeichnet)

Neigung bei Brennschluss (20%)97.4

Nick/Gier-Rate (30%)93.9

Coning · boost (25%)77.8

Schubgeradheit (15%)76.4

Launch tilt 1° · Coning 25.4/53.3°/s · Spin 444.5°/s · Thrust 94.9%

About this score

Worked out from the flight log between liftoff and 80% of apogee, independent of the angle the altimeter was mounted at in the airframe.

Neigung bei Brennschluss (20%) – how close to vertical it left the rod.

Nick/Gier-Rate (30%) and Coning · boost (25%) – how much the nose swung off the rocket's own axis. The main factor.

Schubgeradheit (15%) – how cleanly the motor pushed along the body.

Spin about the rocket's own axis is not counted against it — a fast, straight spin is stable. The line under the bars shows the raw measurements.

Geschwindigkeit

Max. Aufstieg

155.11 m/s

Max. Abstieg

-10.35 m/s

Bei Brennschluss

146.410 m/s

Landegeschw.

-7.032 m/s

Abstiegsgeschw.

-6.432 m/s

Auswurfgeschw.

132.02 m/s

Recovery

Single deploy (no dual deploy detected)

Beschleunigung

Max. Aufstieg

31.08 G

Max. Abstieg

43.02 G

Max. während Brennen

16.85 G

Durchschn. Aufstieg

1.2 G

Durchschn. Brennen

11.73 G

Zeiten

Brennschluss (erster)

1.38 seconds

Apogäum

11.49 seconds

Möglicher Auswurf

1.989 seconds

Landung

129.3 seconds

Ausgang #1 EIN

0 seconds

Ausgang #1 AUS

0 seconds

Winkel

Rampen-Neigung

1.25°

Thrust calc pad tilt

1°

Max. Neigung bis Brennschluss

25.78°

Start-Roll

-1.10°

Start-Nick

-0.55°

Max. Drehung (Brennen)

3004.37 dps

Durchschn. Drehung (Brennen)

340.71 dps

Allgemein

Upload-Datum

14-Jun at 15:01

Datenpunkte

12572

Gesamte Aufnahmezeit

154.900 s

Durchschn. Abtastrate/s

81.1

Anzahl Sperren

Aufnahme-Höhe

41.04 m

Start nach Einschalten

7m 9s

Referenzachse

Batterie & Temperatur

Batterie Start

62%

Batterie Ende

42%

Temperatur Start

26.38°C

Temperatur Ende

27.17°C

MT1 Starttemp.

0°C

Ausgangsregeln

Keine Regeln konfiguriert

Flugdaten-Animation

FLIGHT 1785

756.69 Meters

ALTITUDE

0.00m

VELOCITY

0.00m/s

ACCEL

0.00G

TILT

0.00°

PITCH

0.00°

ROLL

0.00°

YAW

0.00°

TIME

0.00s

AWAITING LAUNCH

ALT

altimetercloud.com

LAUNCH T+0.00s LANDING

Hinweis: Die Fluganimation erfordert eine feste Ausrichtung Ihres Höhenmessers. Kalibrieren Sie Ihre Sensoren für beste Ergebnisse.

Benutzernotizen

A test of 2x Mercury and 2x Nano altimeters in a Lil Nuke with a G80 Aerotech motors.

Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten

Youtube-Video

Kein Video

Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten

Flugbilder (0)

Keine Bilder

Verknüpfte Rakete

✅ Active

My Lil Nuke #1

LOC Precision — Lil' Nuke

✈️ 7 flights linked

Type

Kit build

Diameter

57.4mm

Length

749.3mm

Dry weight

368.5g

Mod

Modified

Stages

Fins

Recovery

Parachute

Chute

61cm

Body

Loc paper tube

💬 7 comments · 👍 2 reactions

View rocket

Sim data from sim files

Motor	Alt	Vel	Accel	Apogee	Source
Estes A8-3	135.3 m	64.8 m/s	29.6 G	4.5 s	RockSim (estes_viking.rkt)
Estes B4-4	282.9 m	105.3 m/s	30.0 G	6.1 s	RockSim (estes_viking.rkt)
Estes B6-4	288.1 m	116.9 m/s	31.0 G	5.9 s	RockSim (estes_viking.rkt)
Estes C6-5	475.1 m	171.4 m/s	34.4 G	7.5 s	RockSim (estes_viking.rkt)
Estes C6-7	483.1 m	171.4 m/s	34.4 G	8.1 s	RockSim (estes_viking.rkt)

Geräteinformationen

Mercury V1

Dieser Flug wurde mit einem geflogen: Mercury V1.

Hardwareversion

Rev 3

Softwareversion

2.40

Zuletzt online

14-Jun at 15:01

Beschleunigungssensor

32G 3-axis

Gyroskop

2000 dgps 3-axis

Drucksensor

Bosch BMP 581

Magnetometer

N/A

1 Mehr von diesem Höhenmesser → 1 Tag: #TEST-LEFT-3 → Höhenmesser-Spezifikationen →

Flugmotoren

1st Stage

AeroTech

G80T-10

Details ▾

Fügen Sie dieses Gerät Ihrem Konto hinzu, um zu bearbeiten

Motorbrenndauer

The dashed line is the combined thrust curve for your motors (data from thrustcurve.org), scaled so its peak matches the recorded acceleration maximum — the shape is meaningful, the absolute level is not (your rocket's weight is unknown).

Startplatz, Datum & Uhrzeit

Klicken Sie auf die Karte · Ziehen zum Anpassen

Lat— Lng—

✓ Launch location saved successfully.

✗ Could not save location — please try again.

Ausgangsregeln

Regeln ermöglichen dem Mercury Aktionen basierend auf Flugbedingungen. Jede Regel hat bis zu 4 Bedingungen (A-D).

Rule 1

After launch onlyANY condition (OR)Active during lockout

ACTION:OUTPUT #1

Conditions

AData 300>0

BHighest Gyro axis (dps)>0

CAcc magnitude (G)>0

DAcc magnitude (G)>0

❌Nicht ausgelöst

Rule 2

After launch onlyANY condition (OR)Active during lockout

ACTION:Action 6000000

Conditions

AData 250>0

BAltitude above pad (m)>0

CAltitude above pad (m)>0

DAltitude above pad (m)>0

❌Nicht ausgelöst

Rule 3

After launch onlyANY condition (OR)Active during lockout

ACTION:OUTPUT #1

Conditions

AAltitude above pad (m)>0

BAltitude above pad (m)>0

CAltitude above pad (m)>0

DAltitude above pad (m)>0

❌Nicht ausgelöst

Rule 4

After launch onlyANY condition (OR)Active during lockout

ACTION:OUTPUT #1

Conditions

AAltitude above pad (m)>0

BAltitude above pad (m)>0

CAltitude above pad (m)>0

DAltitude above pad (m)>0

❌Nicht ausgelöst

Rule 5

After launch onlyANY condition (OR)Active during lockout

ACTION:OUTPUT #1

Conditions

AAltitude above pad (m)>0

BAltitude above pad (m)>0

CAltitude above pad (m)>0

DAltitude above pad (m)>0

❌Nicht ausgelöst

Rule 6

After launch onlyANY condition (OR)Active during lockout

ACTION:OUTPUT #1

Conditions

AAltitude above pad (m)>0

BAltitude above pad (m)>0

CAltitude above pad (m)>0

DAltitude above pad (m)>0

❌Nicht ausgelöst

Motor-Zuordnung (BETA)

Noch im Testmodus! Wir arbeiten daran, den passenden Motor für einen Flug zu ermitteln.

Marke

Motor

Punkte

Form

Brennen

AeroTech

J615ST

142

93.1%

97.7%

AeroTech

H195NBT

110

82.1%

96.8%

Cesaroni

G125-RL

104

84.5%

94.3%

AeroTech

I600R

104

82.8%

91%

AeroTech

J825R

104

84.7%

94.6%

Cesaroni

G118-BS

100

83.5%

95.8%

Cesaroni

H163-WT

100

81.6%

95.4%

Cesaroni

G83-BS

83.9%

94.2%

Cesaroni

H133-BS

85.8%

94.1%

Cesaroni

H255-BS

85.8%

91.2%

Flugvergleich

Comparing against 3 other flights with the same motor configuration.

Highest apogee756.69 m 3rd of 4

The maximum altitude reached above the launch point.

you

best

best 756.82 m · Lil Nuke - Flight with 4 altimeters - 1 (#1784)

Best stability85.3 /100 4th of 4

How straight it flew: launch, coning and thrust straightness combined. 100 is perfect.

you

best

best 86.2 /100 · Lil Nuke - Flight with 4 altimeters - 4 (#1796)

Fastest velocity155.11 m/s 4th of 4

Peak ascent velocity recorded during the flight.

you

best

best 159.41 m/s · Lil Nuke - Flight with 4 altimeters - 4 (#1796)

Best avg burn G11.73 G 2nd of 4

Average acceleration during the motor burn, in G.

you

best

best 11.98 G · Lil Nuke - Flight with 4 altimeters - 1 (#1784)

Longest flight154.9 s 2nd of 4

Total recording time from launch to landing.

you

best

best 155 s · Lil Nuke - Flight with 4 altimeters - 1 (#1784)

Lowest spin340.71 dps 2nd of 4

Average spin rate during the burn.

you

best

best 324.26 dps · Lil Nuke - Flight with 4 altimeters - 1 (#1784)

Coldest flight26.38 C 3rd of 4

Board temperature at launch.

you

best

best 0.28 C · Lil Nuke - Flight with 4 altimeters - 3 (#1786)

🌲 Is it in a tree?41.04 m 3rd of 4

Just for fun: whichever flight came down closest to 8 m above the launch point (roughly tree height) is the one most likely stuck up a tree.

8 m

you

best

closest to 8 m · Lil Nuke - Flight with 4 altimeters - 4 (#1796) at -2.02 m

Allgemeine Flugeinstellungen

Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen. Gehen Sie zur Gehen Sie zur Meine Geräte Seite und konfigurieren Sie die Einstellungen..

Prognosedruck

Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!

Xcweather.co.uk is a decent place to grab pressures from for your location and time.

1013.2 mbar

Starterkennung

This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.

The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.

For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.

25 meters

Abtastverhältnis

The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.

Max. Abtastungen

This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.

18000

Aufnahme-Stopp

This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.

The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).

Auto: 450 samples stable (~9s)

Oversampling

Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.

The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.

16x Oversampling

IIR-Filter

The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.

We suggest not setting this too high as it will cause delay to changes in altitude if set very high.

COEFF 7

Druckfilter

This filter is a software Kalman filter that runs on the altimeters processor.

The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.

Kalman 2 (default)

Sperränderung

This is how we detect a lockout. If the pressure changes by this much in a single sample downwards (pressure increase, lower altitude) then it's likely to be a false reading. Multiply the setting by 32 to get the speed in meters per second that it will trigger at.

0.5 meters

Sensorsynchronisation

The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data. The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.

AKTIVIERT (13 samples / 71.00ms)

Ausrichtung

This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.

Upwards (text up)

IMU-Filter

The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical. These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.

Madgwick 6-Axis

Start-ALP

This is prevention against accidental launch detection.

With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.

With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.

There are very few situations where this option would cause issues, so we suggest leaving it on.

1.4G

Startsperre

When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.

DISABLED

Statische Temperatur

A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.

15.00 °C

Temp.-Sensor

If an external MT1 temperature sensor is connected, this controls whether it is used for logging only or also for altitude calculations.

DISABLED

Ausgangseinstellungen

Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen.

Ausgang 1 aktiviert

Disable or enable the output from being able to turn on or off.

DEAKTIVIERT

Ausgang 1 Auslöser

After apogee (altitude)

This method triggers when the altitude drops below the set altitude after apogee is detected.

After apogee (time)

This method triggers the defined seconds after apogee is detected.

After launch (altitude)

This method is activated if/once the altimeter exceeds the set altitude after launch.

After launch (time)

This option triggers the defined seconds after launch is detected.

After burnout (time)

This method triggers the defined seconds after burnout is detected.

After apogee (altitude)

Ausgang 1 Einschaltzeit

This is how long the output should trigger ON state when the rules are met.

2000ms

Ausgang 1 Höhe

This is the altitude to trigger at if using a trigger method that works on altitude.

For example if you set this to 75m and After apogee (altitude) for the trigger then the output will turn on at 75m on descent above the launch altitude.

0 meters

Ausgang 1 Zeit

This is the time variable for output triggers that work on time.

For example if you set this to 3 seconds and After apogee (time) as the trigger then the output will turn on 3 seconds after apogee.

0 seconds

Höhensperre

Altitude lock is a safety feature that prevents the output from triggering if the altitude is below this level when the rules are met.

0.00 m

Neigungssperre

This is another safety feature. It can be used to disable the output if the rocket has gone too far from vertical.

For example if you set the tilt angle lock to 40 degrees then the output will not fire if the rocket is more than 40 degrees from vertical. To disable set this to 0.

0.00 °

Sensorkalibrierung

Kalibrierungsversätze für diesen Flug.

Gyroskop

-0.220°

-0.650°

1.430°

Beschleunigungssensor

11.170 mG

3.330 mG

27.110 mG

Geräteeinstellungen

Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen.

Geräte-TAG

A custom name or tag assigned to this device for easy identification.

TEST-LEFT-3

Sprache

The language setting configured on the device.

Abschaltmodus

Controls what happens after recording. Standard shuts down normally, Delayed keeps WiFi on for 30 seconds after landing, Stay on keeps the device powered on.

Delayed 30s

LED-Helligkeit

The brightness level of the LED indicators on the Mercury. Lower values save battery.

20%

WLAN-Sendeleistung

WiFi transmit power level. Higher gives better range but uses more battery.

2 dBm (low)

Schlafmodus

Controls whether the device enters low-power sleep when idle.

Normal (sleep when idle)

Batterieüberwachung

Monitors battery voltage during the flight.

DISABLED

Cloud-Gruppe

The cloud group / category this flight is assigned to.

GP6 / GP7 Anschlüsse

Konfiguration der GP6- und GP7-Ausgänge. Diese können Pyrokanäle, Servos oder andere Geräte ansteuern.

Kanal 6 Modus

ON = HIGH

Ch6 min pulse (µs)

Ch6 max pulse (µs)

Ch6 frequency

0 Hz

Ch6 angle ON

0.00°

Ch6 angle OFF

0.00°

Ch6 on time

0.00s

Kanal 7 Modus

ON = HIGH

Ch7 min pulse (µs)

Ch7 max pulse (µs)

Ch7 frequency

0 Hz

Ch7 angle ON

0.00°

Ch7 angle OFF

0.00°

Ch7 on time

0.00s

I2C PCA9685 Servoplatine

Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen.

Konfiguration der externen I2C PCA9685 Servo-Erweiterungsplatine mit bis zu 6 zusätzlichen Servokanälen.

Für diesen Flug war keine I2C-Servoplatine angeschlossen.

Vorhersage und Luftbremsen

Dies ist ein Schnappschuss der für diesen Flug verwendeten Einstellungen.

Der Mercury kann das Apogäum während der Freiflugphase vorhersagen. Diese Einstellungen steuern die Berechnung und das Luftbremsensystem.

Trockenmasse

The total mass of the rocket after motor burnout (dry mass). This is used for the ballistic prediction of apogee altitude. Enter the mass without the motor propellant, or the mass at burnout.

$tc_not_configured

Widerstandsbeiwert

The aerodynamic drag coefficient (Cd) of the rocket. This is used with the rocket area to calculate aerodynamic drag during coast. A typical model rocket has a Cd of 0.4 to 0.8. You can find this value from OpenRocket or RockSim simulations.

$tc_not_configured

Bezugsfläche

The cross-sectional reference area of the rocket in square meters. This is typically the area of a circle with the body tube diameter. For example a 38mm tube has an area of approximately 0.00113 m².

$tc_not_configured

Gas constant

The specific gas constant for dry air, used in the atmospheric model for altitude and density calculations. The standard value is 287.05 J/(kg·K). You shouldn't need to change this unless you know what you're doing.

$tc_not_configured

Die folgenden Einstellungen konfigurieren das Luftbremsensystem.

Luftbremse aktiviert

Enables or disables the active air braking system. When enabled, the Mercury will deploy air brakes via the configured servo channel to try and reach the target altitude. Firmware 2.1+ required.

OFF (default)

Servo channel

Which servo output channel the air brake mechanism is connected to. GP6 and GP7 are the two onboard servo headers, I2C channels are for an external servo expander board.

GP6

Deploy speed

The speed at which the air brakes deploy. The Mercury gradually increases the servo angle until the predicted apogee matches the target rather than going full on/off. This setting controls how quickly it ramps up to full braking.

Medium (default)

Zielhöhe

The target apogee altitude in meters. The air brake system will try to slow the rocket so it reaches this altitude.

$tc_not_configured

Over shoot %

The percentage over the target altitude to aim for until within 15% of the target. This helps prevent undershooting if the prediction is slightly off early in the coast. For example, with a 1000m target and 5% early adjustment, the Mercury will aim for 1050m until it passes 850m.

$tc_not_configured

Activation altitude

The air brake system activates after burnout, but won't engage until the rocket has reached this percentage of the target altitude. This prevents the brakes from deploying too early when predictions may be less accurate.

20% (default)

Flug
Kommentare

Kommentare

Anmelden um zu kommentieren.