Distancia
Elija la unidad de distancia: Metros(m), Pies(ft), Millas(mi) o Kilómetros(km)
Velocidad
Elija la unidad de velocidad: m/s, ft/s, mph o km/h
Aceleración
Elija la unidad de aceleración: m/s² o G
Vuelo 3038

Cosmic Cascade flight 17

Nano V1 Rev 4 · firmware 1.65Secure logSecure logThe altimeter signed this log and it passed verification on upload, so the data is unchanged since the device wrote it.Signatures use Ed25519, which no current technology can forge.
Apogeo
76.09m
5.31 s after launch
Máx. ascenso
33.66m/s
peak ascent
Máx. durante combustión
16.82G
during the burn
Aterrizaje
20.96s
touchdown 4.36 m/s
ZOOM TO
s
s
Mostrar eventos
Ajustar temp. & presión ?
Imagen
Zoom
Clic y arrastre, o pellizco en móvil
Comparar vuelo ?
Resumen del vuelo

The flight, moment by moment

Liftoff
0 s
Inclinación rampa63.10°
Thrust calc pad tilt0.7°
Launch detected
1.904 s
Altitud30.02 m
Velocidad25.32 m/s
Fin combustión (primero)
2.21 s
Altitud38.13 m
Velocidad26.970 m/s
Apogeo
5.31 s
Altitud76.09 Metros
Incl. máx. hasta fin comb.40.31°
Posible eyección
6.967 s
Altitud64.63 m
Velocidad-10.08 m/s
Aterrizaje
20.95 s
Altitud-0.88 m
Máx. descenso-14.18 m/s

Estabilidad86.7%Excelente

Inclinación al apagado (20%)98.1
20% · Launch tilt 0.7°
Cabeceo/guiñada (30%)85.1
25% · Coning 41.7/48.7°/s
Coning · boost (25%)80.7
25% · Spin 43°/s
Rectitud de empuje (15%)85.5
30% · Thrust 97%

Rocket information

Calculated from the flight data alone
Boost acceleration12.2 m/s²
average over the burn · 1.2 g
Coast deceleration8.7 m/s²
average · gravity plus drag
Chute opening peak43.47 G
largest deceleration after ejection
Average descent rate4.68 m/s
ejection to landing · 13.98 s
Batería & temperatura 67% → 67% · Temperatura inicio 28.41 → 29.1 °C · Lanzamiento tras encendido 5m 8s

About the stability score

Worked out from the flight log between liftoff and 80% of apogee. It is independent of the angle the altimeter was mounted at, so it measures the flight rather than the fitting.

Inclinación al apagado (20%)20%How close to vertical it left the rod.
Cabeceo/guiñada (30%)25%How much the nose swung off the rocket's own axis across the whole ascent.
Coning · boost (25%)25%The same swing during the burn, when it matters most.
Rectitud de empuje (15%)30%How cleanly the motor pushed along the body.

Spin about the rocket's own axis is not counted against it — a fast, straight spin is stable. The figures beside the score are the raw measurements behind these four.

Altitud
Apogeo76.09 Metros
Tiempo al apogeo5.31 s
Altitud fin combustión38.13 m
Altitud vel. máx.47.5 m
Altitud eyección64.63 m
Altitud aterrizaje-0.88 m
Altitud grabación-42.64 m
Velocidad
Máx. ascenso33.65 m/s
Máx. descenso-14.18 m/s
En fin combustión26.970 m/s
Vel. descenso-5.060 m/s
Vel. eyección-10.08 m/s
Vel. aterrizaje-4.358 m/s
Aceleración
Máx. durante combustión16.82 G
Máx. ascenso16.82 G
Máx. descenso43.47 G
Prom. ascenso0.87 G
Prom. combustión1.78 G
Tiempos
Fin combustión (primero)2.21 s
Apogeo5.31 s
Posible eyección6.967 s
Aterrizaje20.95 s
Ángulos
Inclinación rampa63.10°
Thrust calc pad tilt0.7°
Incl. máx. hasta fin comb.40.31°
Alabeo al lanzamiento-21.19°
Cabeceo al lanzamiento60.94°
Giro máx. (comb.)1927.01 dps
Giro prom. (comb.)73.77 dps
Recovery
Single deploy
No dual deploy detected on this flight.
General
Fecha subida07/10/26-23:59:35
Muestras de datos4762
Tiempo total grabación36.754 s
Prom. muestras/s129.5
Número de bloqueos0
Lanzamiento tras encendido5m 8s
Eje de referenciaX
Batería & temperatura
Batería inicio67%
Batería fin67%
Temperatura inicio28.41°C
Temperatura fin29.1°C
Notas del usuario

Pitched significantly into the breeze such that staging took place seemingly horzontally. Recovered on the field well to the east.

Añada este dispositivo a su cuenta para editar
Vídeo Youtube
Sin vídeo
Añada este dispositivo a su cuenta para editar
Imágenes del vuelo 0
Sin imágenes
Motores del vuelo
1st stage
1×C6-0EstesDetails
Burn time
1.86 s
Diameter
18.00 mm
Average thrust
4.74 N
Max thrust
14.09 N
Total weight
24.10 g
Propellant weight
10.80 g
Propellant type
black powder
Impulse8.82Ns
Max thrust14N
Burn time1.86s
Impulse classC
1st stage thrustloading curve…
Motor data by ThrustCurve.org
2nd stage · 5s delay
1×A8-5EstesDetails
Burn time
0.73 s
Diameter
18.00 mm
Average thrust
3.18 N
Max thrust
9.73 N
Total weight
16.30 g
Propellant weight
3.30 g
Propellant type
black powder
Impulse2.5Ns
Max thrust9.7N
Burn time0.73s
Impulse classA
2nd stage thrustloading curve…
Motor data by ThrustCurve.org
Combined

Every stage on one time base, each ignited at the previous stage's burnout. Motors in a cluster are summed within their own stage.

Total impulse11.32Ns
Max thrust14N
Total burn2.59s
Combined classD
Combined thrustloading curve…
Motor data by ThrustCurve.org
Añada este dispositivo a su cuenta para editar
Cohete vinculado
Ningún cohete vinculado a este vuelo
Flight mass
Liftoff mass114.1gestimated
Mass at burnout103.3gestimated
No mass is set for this flight, so Motor thrust (N) uses a mass estimated from the measured burn and the motors’ rated impulse. Set the rocket’s mass for the measured impulse and specific impulse.
Motor thrust (N) is on the chart, under Acceleration.

Other flights on this motor

1 · highest first

Linked flights

Connect flights that belong together: a second altimeter flown in the same rocket, or the same rocket flown again. Linked flights appear on each other’s pages.

No linked flights yet.

Sitio de lanzamiento, fecha y hora

Haga clic en el mapa para marcar su sitio de lanzamiento. Cambie entre vista de mapa y satélite.

Imagery © Esri, Maxar, Earthstar Geographics

Clic en el mapa · Arrastre para ajustar

Canopy height from the Meta and WRI High Resolution Canopy Height Maps v2 (Meta and World Resources Institute, 2026; source imagery © 2016 Vantor), used under CC BY 4.0. Ground elevation built from Terrain Tiles (Mapzen and AWS Open Data), derived from 3DEP and GMTED courtesy of the U.S. Geological Survey, SRTM courtesy of NASA, and ETOPO1 courtesy of NOAA. Map and imagery credited on the view above.

Site nameSixty Acres Park NorthLat47.706374Lng-122.140428Ground level9.0 m · 30 ftFecha lanzamiento—Hora lanzamiento—
Animación de datos

FLIGHT 3038

76.09 Meters

ALTITUDE
0.00m
VELOCITY
0.00m/s
ACCEL
0.00G
TILT
0.00°
PITCH
0.00°
ROLL
0.00°
YAW
0.00°
TIME
0.00s
AWAITING LAUNCH
ALT
altimetercloud.com
LAUNCH T+0.00s LANDING

BURNOUT

Motor burn complete

Nota: La animación de vuelo requiere que su altímetro esté montado en una orientación fija. Calibre sus sensores para mejores resultados.
Nano V1
Revision 4
Nano V1
Este vuelo se realizó con un Nano V1.
The hardware
Versión hardwareRev 4
Versión software1.65
Última conexión07/10/26-23:59:35
Sensor presiónBosch BMP 581
Acelerómetro32G 3-axis
Giroscopio2000 dgps 3-axis

Flights from this altimeter

20 of 25

Settings, as they were for this flight

Ajustes generales del vuelo
Presión prevista
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!

Xcweather.co.uk is a decent place to grab pressures from for your location and time.
1013.2 mbar
Detección lanzamiento
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.

The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.

For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
30 meters
Sample ratio
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:1:1 (200Hz)
Max samples
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
38000
Recording stop
i
This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.

The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Auto: 8s stable altitude
Oversampling
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.

The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
16x Oversampling
IIR filter
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.

We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
COEFF 7
Pressure filter
i
This filter is a software Kalman filter that runs on the altimeters processor.

The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
TruePath
Sample speed
i
The sample rate of the altimeter's sensors. 50Hz takes 50 samples per second, 100Hz takes 100 samples per second for higher resolution data.
200 Hz
Hybrid mode
i
When enabled, the altimeter records at full speed during ascent then switches to half speed after apogee to extend recording time during descent.
Enabled
Sync sensors
i
The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data. The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.
ACTIVADO (22 samples / 108.92ms)
Orientation
i
This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.
Down (text up)
IMU filter
i
The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical. These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.
Madgwick 6-Axis
Launch ALP
i
This is prevention against accidental launch detection.

With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.

With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.

There are very few situations where this option would cause issues, so we suggest leaving it on.
2.0G
Launch lock
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
DISABLED
Static temperature
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C
Calibración de sensores
Compensaciones de calibración usadas en este vuelo.
Giroscopio⚠ El giroscopio no ha sido calibrado
X0.000°
Y0.000°
Z0.000°
Acelerómetro⚠ El acelerómetro no ha sido calibrado
X0.000 mG
Y0.000 mG
Z0.000 mG

Files

Where the altimeter signs its log, the file carries that signature and a tick beside it. A tick means the data is unchanged since the device wrote it, which is what a record claim needs.
CSV
3038.csv ✓ SIGNED
The log as columns of text. Opens in a spreadsheet, and in every simulator that reads flight data.
443 KB
LOG
3038.aclz ✓ SIGNED
The altimeter's own compressed log, exactly as the device wrote it. This is the file to keep for a record claim.
49 KB
Adjusted CSV2904 recalculated in your browser
The log recomputed for your own sea-level pressure and temperature. Columns: time, altitude as recorded and adjusted, raw altitude as recorded and adjusted, pressure.

This file is built here from the signed log, so it carries no signature of its own. Anyone verifying a claim should be sent to the flight page and build their own from the original.

Vuelo
Comentarios
Inicia sesión para comentar.
Inicia sesión para comentar.