Arreaux Ascender F115
Mercury Plus Rev 0 · firmware 1.00
Apogeu
559.36m
10.08 s after launch
Máx. subida
261.73m/s
peak ascent
Máx. durante combustão
38.5G
during the burn
Aterragem
63.61s
touchdown 5.63 m/s
ZOOM TO
s
s
Something look wrong with this flight's data?
Resumo do voo
The flight, moment by moment
Liftoff
0 s
Ângulo da rampa2.8°
Orientação4.96°
Launch detected
0.3 s
Altitude35.38 m
Velocidade176.31 m/s
Fim combustão (primeiro)
0.72 s
Altitude130.26 m
Velocidade134.520 m/s
Apogeu
10.08 s
Altitude559.36 Metros
Incl. máx. até fim comb.7.77°
Possível ejeção
10.364 s
Altitude558.15 m
Velocidade-4.51 m/s
Aterragem
63.61 s
Altitude0.7 m
Máx. descida-44.04 m/s
Estabilidade85.6%Excelente
Inclinação no fim da queima (20%)92.9
20% · Rail angle 2.8°
Taxa arfagem/guinada (30%)97.4
25% · Coning 16.1/40.6°/s
Coning · boost (25%)85.8
25% · Spin 252.2°/s
Retidão de empuxo (15%)70.8
30% · Thrust 93.7%
Rocket information
Calculated from the flight data alone
Boost acceleration186.8 m/s²
average over the burn · 19.1 g
Coast deceleration14.4 m/s²
average · gravity plus drag
Ballistic coefficient328 kg/m²
fitted to the 9.36 s coast
Apogee lost to tilt0.33 m
flown vertical ≈ 559.6 m · from the tilt at burnout
Chute opening peak39.92 G
largest deceleration after ejection
Average descent rate10.46 m/s
ejection to landing · 53.25 s
Bateria & temperatura 89% → 84% · Temperatura início 21.12 → 21.77 °C · Lançamento após arranque 15m 6s
Altitude
Apogeu559.36 Metros
Tempo até apogeu10.08 s
Altitude fim combustão130.26 m
Altitude vel. máx.70.02 m
Altitude ejeção558.15 m
Altitude aterragem0.7 m
Altitude gravação131.32 m
Velocidade
Máx. subida261.73 m/s
Máx. descida-44.04 m/s
No fim combustão134.520 m/s
Vel. descida-9.923 m/s
Vel. ejeção-4.51 m/s
Vel. aterragem-5.631 m/s
Aceleração
Máx. durante combustão38.5 G
Máx. subida38.5 G
Máx. descida39.92 G
Média subida1.08 G
Média combustão19.36 G
Tempos
Fim combustão (primeiro)0.72 s
Apogeu10.08 s
Possível ejeção10.364 s
Aterragem63.61 s
Saída #1 ON0 s
Saída #1 OFF0 s
Ângulos
Ângulo da rampa ?2.8° ± 4.01°
Desvio da rampa ?não medido
Incl. máx. até fim comb. ?7.77°
Orientação ?4.96°
Desalinhamento de montagem ?não medido
Rolagem no lançamento-3.62°
Arfagem no lançamento3.39°
Rotação máx. (comb.)326.73 dps
Rotação média (comb.)82.17 dps
Recovery
Single deploy
No dual deploy detected on this flight.
Geral
Data envio24-Oct at 23:11
Amostras de dados9232
Tempo total gravação88.800 s
Média amostras/s103.9
Número de bloqueios1
Lançamento após arranque15m 6s
Eixo de referênciaX
Bateria & temperatura
Bateria início89%
Bateria fim84%
Temperatura início21.12°C
Temperatura fim21.77°C
Temp. MT1 lançamento0°C
Something look wrong with this flight's data?
Notas do utilizador
Sem notas
Adicione este dispositivo à sua conta para editar
Vídeo Youtube
Adicione este dispositivo à sua conta para editar
Imagens do voo 0
Sem imagens
Flown as
Rocket
Motor configuration
Custom
1× AeroTech F115SN-12A-10, set on this flight
Loaded weight
518.8 g
set on this flight · estimated 533.2 g from the rated impulse
Measured burn
from this flight’s thrust and its loaded weight
Total impulse, NFPA 112576.58 Ns
rated 79.15 Ns, 3.2% under, within the 20% NFPA 1125 allows
Total impulse, absolute76.93 Ns
Measured asF107
sold as a F115SN-12A
Burn time, NFPA 11250.72 s
0.08 to 0.79 s
Average thrust106.7 N
impulse over burn time
Peak thrust200.8 N
at 0.10 s
Specific impulse204 s
38.5 g of propellant
Mass at burnout480.3 g
loaded weight less propellant
NFPA 1125, the code motors are certified to by NAR, Tripoli and CAR: the burn runs from where the thrust first rises above 5% of its peak to where it falls below it (7.8.3), and the total impulse from that rise to the last measurable thrust before ejection (7.8.5). Absolute counts every newton from liftoff. The same code lets a production lot vary 20% from its mean impulse for a model rocket motor and 10% for high power (7.8.6). Both figures follow the loaded weight: 1% out on the weight is about 1% out on the impulse.
Motores do voo
1st stage · 10s delay
Burn time
0.69 s
Diameter
29.00 mm
Average thrust
114.16 N
Max thrust
146.7 N
Total weight
92.50 g
Propellant weight
38.50 g
Propellant type
Slo Nine
Links
Impulse79.15Ns
Max thrust146.7N
Burn time0.69s
Impulse classF
1st stage thrustloading curve…
Motor data by ThrustCurve.org
Adicione este dispositivo à sua conta para editar
Foguete associado
🚀
Active
Arreaux Ascender
Type
Scratch built
Diameter
50.8mm
Length
1041.4mm
Empty weight
15g
Stages
1
Fins
3
Body
Kraft paper
Rule events
No output rules fired during this flight.
Correspondência motor (BETA)
Ainda em modo de teste! Estamos a descobrir qual motor foi usado no voo.
Marca
Motor
Pontuação
Forma
Comb.
AeroTech
F115SN
122
94%
98.3%
AeroTech
H283ST
111
93.2%
94.5%
Cesaroni
H399-WT
109
89.4%
93.2%
Cesaroni
F70-WT
100
92.8%
98.3%
AeroTech
J1799N
95
89.3%
95.1%
AeroTech
D21T
90
90.5%
95.3%
Cesaroni
H340-SS
90
90.6%
95.7%
Cesaroni
H255-WT
84
91.4%
93.6%
AeroTech
I599N
84
84.5%
90.9%
AeroTech
J1299N
84
85.7%
91.3%
Linked flights
No linked flights yet.
Local de lançamento, data e hora
Imagery © Esri, Maxar, Earthstar Geographics
Clique no mapa · Arraste para ajustar
Canopy height from the Meta and WRI High Resolution Canopy Height Maps v2 (Meta and World Resources Institute, 2026; source imagery © 2016 Vantor), used under CC BY 4.0. Ground elevation built from Terrain Tiles (Mapzen and AWS Open Data), derived from 3DEP and GMTED courtesy of the U.S. Geological Survey, SRTM courtesy of NASA, and ETOPO1 courtesy of NOAA. Map and imagery credited on the view above.
Site nameJMRC 1Lat42.200046Lng-83.965386Ground level292.8 m · 961 ftData lançamento2026-10-24Hora lançamento10:33
Taken from the NOAA GFS weather model for this place and time, so there is nothing to enter. Weather data by Open-Meteo.com (CC BY 4.0). The full weather for 48 hours either side, within 15 km, is in the tabs below and in Downloads.
Temperature12.6 °C
Sea-level pressure1031.2 hPa
QNH1031 hPa
Wind speed2.4 m/s
Wind directionESE
Cloud coverClear
About sea-level pressure and QNH
Sea-level pressure is kept as given: the model’s own, or the figure entered from a forecast or report. QNH is that pressure the way an altimeter setting means it, through the standard atmosphere, and is what the adjusted apogee and the adjusted CSV use.
Model values, not observations. NOAA GFS: weather data by Open-Meteo.com (CC BY 4.0). Ensemble: NOAA GEFS.
Animação dos dados
FLIGHT 3161
559.36 Meters
ALTITUDE
0.00m
VELOCITY
0.00m/s
ACCEL
0.00G
TILT
0.00°
PITCH
0.00°
ROLL
0.00°
YAW
0.00°
TIME
0.00s
AWAITING LAUNCH
ALT
altimetercloud.com
LAUNCH
T+0.00s
LANDING
BURNOUT
Motor burn complete
Nota: A animação de voo requer que o altímetro esteja montado numa orientação fixa. Calibre os sensores para melhores resultados.
Rocketry Ltd
Mercury Plus
Altímetro de Alto Desempenho com WiFi Habilitado 256G. Este voo foi realizado num Mercury Plus.
Versão hardware Rev 0Versão software 1.00Última ligação 08-Nov at 16:36
Especificações
Eletrónica
- Microcontrolador
- ESP32-C632-bit ESP32-C6 160MHz
- Acelerómetro
- ISM6HG2563-axis 256G (High) & 3-axis 16G (Low)
- Barómetro
- Bosch BMP581300 to 1250 hPa within specification
- Giroscópio
- ISM6HG2564000 dgps 3-axis
- Saídas de alta corrente
- 2x 15A high current low resistance high side switches
- Suporte para servos
- Yes: 2 Directly or 16 via the I2C expansion port
Registo de dados
- Taxa de amostragem máxima
- 433 Hz
- Máximo de amostras por registo
- 30,000
- Registo mais longo
- 50 minAt 10Hz although default settings are 433Hz with 1:8 hybrid mode
Tamanho, peso e bateria
- Tamanho
- 30 x 16.9 x 10.8mm
- Peso
- 4.6 g4.6 g com a bateria mais pequena
- Tensão da bateria
- 3 a 4.2 V
- Autonomia da bateria
- 6com a bateria mais pequena
Documentos
Flights from this altimeter
3 of 3
Settings, as they were for this flight
Definições gerais do voo
Pressão prevista
i
Set this to your local forecast pressure at sea level. This will offer you slightly improved accuracty for your flight, although it's not 100% essential every little helps!
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
Xcweather.co.uk is a decent place to grab pressures from for your location and time.
1013.2 mbar
Deteção lançamento
i
This is the altitude above the launch pad altitude where the altimeter will trigger itself into recording / flight mode.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
The altimeter keeps a constant average of the pressure while waiting for launch, it uses a simple algorithm and the pre-flight buffers to do this. The most recent 120 samples (~4 seconds) are ignored so your pre-trigger altitude won't effect the ground baseline.
For almost all uses we suggest keeping this on the 25 Meter (~82 feet) default settings. If you want to test your altimeter by throwing it in the air, or are planning a very low flight you may want to lower the setting.
35 meters
Taxa amostragem
i
The base sample rate of the altimeter's sensors in samples per second. This setting was deprecated in firmware 2.0+.
32 Hz
Sample ratio
i
The altimeter runs at 50Hz however you can record every sample or every X samples in order to extend the log time. For example if you set the ratio to 1 it will save 1:1 samples, or if you set it to 3 it will save 1 in 3 samples.
1:5 (hybrid, reduces after apogee)
Max samples
i
This is the maximum samples the altimeter will log per flight. When it reaches this amount it will stop and save the recording.
18000
Recording stop
i
This setting is how the altimeter decides to stop recording. You can choose either 450 (~9s) or 900 (~18s) samples stable or it will record until the max samples limit unless you press the BUTTON in Manual stop mode.
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
The samples stable method waits for the devices altitude not to change for the set number of samples. This is defined by not changing by more than +/- 1.0 meters for 98% of the samples, it's a reliable method to stop the recording after landing within 8-10 seconds (300 sample) or 16-20 seconds (600 sample).
Auto: 450 samples stable (~9s)
Oversampling
i
Oversampling is a internal setting of the BMP 390 pressure sensor. It is how many samples are taken for each reading. By taking multiple samples for each pressure reading the altimeter reduces noise and increases the resolution of the output.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
The sensor can run at 50 samples per second in 4X mode, so we suggest leaving it in this mode as it will offer the highest accuracy.
16x Oversampling
IIR filter
i
The IIR filter is another internal sensor for the BMP390 pressure sensor. It is a Infinite impulse response filter used to enhance pressure measurement accuracy by reducing noise. It's primarily for smoothing out rapid pressure changes.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
We suggest not setting this too high as it will cause delay to changes in altitude if set very high.
COEFF 7
Pressure filter
i
This filter is a software Kalman filter that runs on the altimeters processor.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
The Kalman filter uses a prediction step based on a system model and then a correction step using new measurements to refine its estimate, it creates accurate most certain results from data with noise in it.
Kalman 2 (default)
Lockout change
i
This is how we detect a lockout. If the pressure changes by this much in a single sample downwards (pressure increase, lower altitude) then it's likely to be a false reading. Multiply the setting by 32 to get the speed in meters per second that it will trigger at.
0.5 meters
Sync sensors
i
The filters on the pressure sensor can cause it to lag very slightly behind the Accelerometer and Gyroscope data.
The Sync sensors option detects how far out of sync these sensors are. It then corrects the Acceleration and Gyroscope readings to match the pressure sensor.
ATIVADO (5 samples / 38.00ms)
Orientation
i
This is the orientation you intend to install the Altimeter in your rocket. It's needed to ensure completly accurate angles and orientation charts and reports. Check out the Manual for more information on this.
Upwards (text up)
IMU filter
i
The IMU filter, or fusion filter takes the data from each axis of the Gyroscope and Accelerometer to calculate the Pitch, Roll, Yaw and tilt angle from vertical.
These filters can build up some discrepency over time so it's important to calibrate your sensors to minimise this.
Madgwick 6-Axis
Launch ALP
i
This is prevention against accidental launch detection.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
With this disabled the launch is based only on pressure and something that creates a low pressure can trigger the flight by accident. For example pulling your nose cone off can even trigger it.
With this enabled the rocket also needs to have seen 8 samples (0.25 seconds) of acceleration above this setting in the last 3 seconds as well as the pressure drop to trigger. There is a backup trigger of 1.05 seconds of altitude being above the launch detect setting too.
There are very few situations where this option would cause issues, so we suggest leaving it on.
1.4G
Launch lock
i
When enabled, the altimeter locks out recording for a set period after power on to prevent false triggering during setup.
DISABLED
Static temperature
i
A fixed temperature value used for altitude calculation when the external temperature sensor is disabled or not connected.
15 °C
Temp sensor
i
If an external MT1 temperature sensor is connected, this controls whether it is used for logging only or also for altitude calculations.
DISABLED
Definições de saída
Arm switch
i
When enabled, GP6 is a hardware arm switch — outputs and rules are held off until the switch is closed to ground.
DISABLED
Startup lockout
i
Outputs and rules are blocked for this many seconds after power-on while sensors settle. 0 = off.
None
Launch confirm delay
i
After launch is detected, outputs and rules won't fire until this many seconds have passed.
2 s
Altitude floor
i
Outputs and rules are blocked until the rocket is at least this height above the launch pad.
50 m
Custom dataset 1
i
User-defined expression evaluated per sample, available for charting.
—
Custom dataset 2
—
Calibração de sensores
Desvios de calibração utilizados neste voo.
Giroscópio⚠ O giroscópio não foi calibrado
X0.000°
Y0.000°
Z0.000°
Acelerómetro⚠ O acelerómetro não foi calibrado
X0.000 mG
Y0.000 mG
Z0.000 mG
Definições do dispositivo
TAG dispositivo
i
A custom name or tag assigned to this device for easy identification.
Merc3532
Idioma
i
The language setting configured on the device.
🇬🇧 English
Modo encerramento
i
Controls what happens after recording. Standard shuts down normally, Delayed keeps WiFi on for 30 seconds after landing, Stay on keeps the device powered on.
Delayed 30s
Brilho LED
i
The brightness level of the LED indicators on the Mercury. Lower values save battery.
20%
WiFi TX power
i
WiFi transmit power level. Higher gives better range but uses more battery.
2 dBm (low)
Modo suspensão
i
Controls whether the device enters low-power sleep when idle.
Normal (sleep when idle)
Monitor bateria
i
Monitors battery voltage during the flight.
DISABLED
Cloud group
i
The cloud group / category this flight is assigned to.
General use
Portas GP6 / GP7
O controlo de portas GP não estava disponível até o firmware 2.0
Placa servo I2C PCA9685
O controlo de portas GP não estava disponível até o firmware 2.0
Previsão e freios aéreos
Esta funcionalidade não estava disponível até à versão 2.10+
Files
Where the altimeter signs its log, the file carries that signature and a tick beside it. A tick means the data is unchanged since the device wrote it, which is what a record claim needs.
CSV
3161.csv
The log as columns of text. Opens in a spreadsheet, and in every simulator that reads flight data.
773 KB
WX
3161_weather.json.gz
The weather for 48 hours either side of the launch, within 15 km of the launch site: NOAA GFS every hour, at the surface and up to about 31 km, and the NOAA GEFS ensemble where this site holds it. JSON, gzip compressed. Weather data by Open-Meteo.com (CC BY 4.0) and NOAA. For 2026-10-24 11:00 local time at 42.2000, -83.9654.
1043 KB
Adjusted CSV2904 recalculated in your browser
The log recomputed for your own sea-level pressure and temperature. Columns: time, altitude as recorded and adjusted, raw altitude as recorded and adjusted, pressure.
This file is built here from the signed log, so it carries no signature of its own. Anyone verifying a claim should be sent to the flight page and build their own from the original.
Custom CSVbuilt in your browser
Pick any of the chart’s data sets, the worked-out ones included, and the part of the flight to cover. Values come in the units the chart is set to.
In the file
Time span
One row for every time any chosen data set has a sample. A data set with no sample at that time is left blank rather than filled in. Built from the chart’s data, so it carries no signature.
Share this flight
Anyone with the link can view this flight; nothing else on your account is shared.
Chart snapshot
A PNG of the chart exactly as you have it set right now: the series you have switched on, your zoom, your labels and any pressure correction applied.
Hotlink images
Stored images of the whole flight, altitude only, not your current chart view. Transparent, regenerated whenever the flight changes, and safe to hotlink on a forum.
Small340 × 255
Large1000 × 750
QR code
Links to this flight page. Useful on a range card or a club display.
Iniciar sessão para comentar.
Iniciar sessão para comentar.