Home
My Devices
Jupiter settings···
Jupiter3640···
connecting…
-
-
—
CPU
20s—
3m—
View all device info →
Position
Sats- -
hAcc-m
HDOP
-
AssistNow
-
GNSS alt
-
Pressure alt
-
Power
Batt-V
Cap-V
4V2-V
CPU 20s-%
CPU 3m-%
Buck boost mode
-
Exp power
-
Signal
CSQ-/31
Net--
RSRP
-
RSRQ
-
Reconn
-
Expansion
EXP1Not connected
EXP2Not connected
EXP3Not connected
EXP4Not connected
Magnetic orientation
Heading
-
Declination
-
Field (µT)
-
Attitude
Roll
-
Pitch
-
Yaw
-
Tilt
-
Thermal
MBoard
-°
DBoard
-°
CPU
-°
Outputs
OUT1-
OUT2-
OUT3-
System
Disk-MB
RAM free
—
Uptime
—
Light (lux)
-
Device
Firmware
-
Boots
-
Last reset
-
Read-only view. This is a shared demo Jupiter, so you can look around every page but nothing can be changed or sent to the device.
Jupiter3640
Live Device Information · 2884-85AE-1B8C
System position
The live fused position the device is using
Position-
Fix-
GNSS alt-
Pressure alt-
Active source-
Sources
Onboard GNSS
Position-
Sats-
hAcc-
Since fix-
Time to fix-
AGNSS-
Constellations-
Additional GNSS #1
Position-
Sats-
hAcc-
Since fix-
Time to fix-
AGNSS-
Not configured
Additional GNSS #2
Position-
Sats-
hAcc-
Since fix-
Time to fix-
AGNSS-
Not configured
Cross-check
GNSS spread-
GNSS vs Cell est.-
Rail voltages
The last 60 seconds of each rail, sampled at 50 Hz. Use refresh to pull it from the device.
Battery
-%
Time left (20 min average)
-
At this load (last 10 min)
-
Pack-
Chemistry-
Empty to full-
Discharge curve
Cellular modem
Current connection
Operator-
Mode-
Transport-
Signal-
RSRP-
RSRQ-
SINR-
Reconnects-
Server round-trip-
Connected for-
Data usage (MQTT)
Sends / min-
Sent / min-
Recv / min-
Sent / hour-
Recv / hour-
Connect / disconnect log
| Loading… |
-
Online history
Availability at one-minute resolution. A full bar is every minute of that bucket reachable;
a short one is an outage. Hover for the split between the cellular broker and the UDP
tracker, which do not always fail together.
Online, last 24 hours
-
Online, last 7 days
-
Online, last 31 days
-
Online, last 365 days
-
Usage history
Daily cellular data over the last 30 days. Hover a point for that day.
Cellular uptime
Last 24 hours
-
Last 7 days
-
Last 31 days
-
Last 12 months
-
Encrypted link · AES-128-CBC
Every MQTT payload is AES-128 encrypted on the device before it leaves over the cellular link, and decrypted only at the server.
MQTT telemetry
Usage above is measured at the server from MQTT payloads only. UDP position packets used in flight, and protocol overhead, are not included.
LoRa modem
Coming soon.
Pressure sensor
Pad altitude, last 20 s
100 Hz pressure altitude above sea level. Shaded band is the floor averaging window; the dashed red line is the pad floor.
Loading…
Sensor detail
SensorBMP581
Output rate-
Pressure-
Altitude (sea level)-
Temperature-
Weather mode-
Sea-level pressure-
Ambient temperature-
Pad floor-
Height above pad-
IMU
X Y Z body axes · labels mark front/back · cylinder = antenna
Orientation & fusion
SensorISM6HG256X
Fusion-
Status-
Roll / pitch / yaw-
Tilt from vertical-
Quaternion w,x,y,z-
Magnetometer
-
Magnetometer
SensorBMM350
Magnetic heading-
Field strength-
Status-
Optical sensor
Illuminance, last 60 s
10 Hz ambient light from the OPT3001, in lux.
Live · 0.5 s average - lux · 20 s average - lux
Loading…
Microphone
Recent audio commands
The last 10 mic arming frames decoded, and whether the code matched the arming PIN.
| Loading… |
Temperature
Temperatures, last 60 s
10 Hz. Pressure sensor (BMP581), daughterboard (TMP102), and CPU core.
Loading…
High-current outputs
Output channels
Igniter continuity over the last 10 s, with live output and power-good state.
Output power enable (Arm mode)-
OUT 1-i
--
OUT 2-i
--
OUT 3-i
--
Loading…
Accessories
Expansion ports
What each port is configured as, and live state where the accessory can report it.
External power switch
The switch on the power-in connector. Shares GPIO12 with the microphone, so it is sampled between mic windows (about every 1.5 s).
-
To fetch, view or download the device's console logs, use the Logging page.
Console logs →
System information
Device diagnostics
Requested from the device on demand, not part of the regular telemetry. Refreshes automatically if the last fetch is over 30 minutes old.
Loading…
Calibration
Sensor calibration
Loading…
Fetching data
Requesting from device
Jupiter settings
Settings sync
We’ll check the device’s settings hash against the website’s copy. These should always be in sync, and this confirms they absolutely are.